| 詳細參數 | |||
|---|---|---|---|
| 品牌 | MOOG | 型號 | G122-829-001 |
| 結構形式 | 模塊式 | 安裝方式 | 控制室安裝 |
| LD指令處理器 | 硬PLC | 功能 | 伺服放大器 |
| 工作電壓 | 電源組24VDC | 環境溫度 | 0to,40,C |
| 環境濕度 | 10至95% | 加工定制 | 否 |
| 重量 | 180g | 產地 | 美國 |
| 外形尺寸 | 100Wx108Hx45D | ||
MOOG G122-829-001 伺服放大器
G122-829A001為通用型，用戶可配置，P-I伺服放大器。放大器內的選擇器開關啟用比例控制、積分控制或兩者都需要挑選出來的。放大器特性的許多方面都可以可使用前面板電位器進行調整，也可使用內部電位器進行選擇開關。這使得一個放大器可以在許多場合使用不同的應用。安裝在垂直后表面上的水平DIN導軌對于工業鋼外殼，是預期的安裝方法安裝G122-829A001的導軌釋放夾應正面朝下，因此前面板和端子標識是可讀的，因此內部電子設備接受冷卻氣流。
模塊放置的一個重要考慮因素是否存在來自其他設備的電磁干擾（EMI）在圍欄里。例如，VF和AC伺服驅動器可產生高水平的電磁干擾。始終檢查其他設備在安裝前的EMC合規性G122-829A001就在附近。
G122-829A001發射的輻射遠低于所稱的水平因?yàn)樗腃E標志測試。因此，不需要特別的預防措施抑制排放所需。但是，豁免外部干擾輻射取決于仔細布線技術?？山邮艿姆椒ㄊ鞘褂闷帘坞娎|所有連接和電纜屏蔽的徑向端接，以一個合適的接地電纜密封套，在進入點工業鋼外殼。如果不可能，請更換機箱。122-829A001上提供了接地螺釘端子。裸露的電線應保持最小長度。連接將電纜兩端的屏幕連接到機箱接地。
The G122-829A001 is a general purpose, user configurable,P-I servoamplifier. Selector switches inside the amplifier enable either proportional control, integral control, or both to be selected. Many aspects of the amplifier’s characteristics can be adjusted with front panel pots or selected with internal switches. This enables one amplifier to be used in many different applications.Horizontal DIN rail mounted on vertical rear surface.For industrial steel enclosures, this is the expected installation b Install the guide rail release clamp of g122-829a001Face down, so front panel and terminal identification.It is readable, so the internal electronic equipment is cooled Airflow.
An important consideration for module placement.Is there electromagnetic interference (EMI) from other equipment.In the fence. For example, VF and AC servo drives.Can produce a high level of electromagnetic interference. Always check.EMC compliance of other equipment before installation G122-829a001 is nearby.
The G122-829A001 emits radiation well below the level called for in its CE mark test. Therefore, no special precautions are required for suppression of emissions. However, immunity from external interfering radiation is dependent on careful wiring techniques. The accepted b is to use screened cables for all connections and to radially terminate the cable screens, in an appropriate grounded cable gland, at the point of entry into the industrial steel enclosure. If this is not possible, chassis ground screw terminals are provided on the G122-829A001. Exposed wires should be kept to a minimum length. Connect the screens at both ends of the cable to chassis ground.
ABB 訂貨號58052515G 型號SCYC51010
ABB 訂貨號3BSE003127R1 型號DSAI130D
INDRAMAT 109-0780-4A01-02
Yamatake EST0240Z05WBX00
Contrex 3200-1677
GALIL DMC-1832
servo MTS30M4-38
MOTOROLA MVME5100
FORCE PMC422FP
BENTLY PWB78434-01
ABB XS321A
AUTOMAX 57C416
MAHR NHT6-100
CORRECT FVL-2X-65D-CA-LED
Pacific Scientific SC753A-001-01
GE H200I
GE 104X905BA603
GE 104X905BA603
GE 12HFA51A42H
GE 12HFA51A42H
GE 12HGA11J52
GE 269 PLUS-D/O-100P-125V
GE 369-HI-0-0-0-0
GE 489-P5-LO-A20
GE 5136-PFB-VME
GE 531X305NTBAPG1
GE 531X305NTBAPG1
GE 531X305NTBAPG1
GE 94-164136-001
GE CT7P70500470CW24
GE DS200ADGIH1AAA
GE DS200TCQAG1BHF
GE HE693STP104AX
GE HE693STP110
GE HE693STP110
GE IC200ALG620
GE IC200CHS001底座
GE IC200GBI001
GE IC3645LXCD1
GE IC3645LXCD1
GE IC3645LXCD1
GE IC3645LXCD1
GE IC660BBD025
GE IC660EBD020
GE IC660ELB912G
GE IC660ELB912G
GE IC660ELD100A
GE IC660TSA100
